Hex | Phillips | Slotted | Machine Screws | Set Screws | U Drive Screws | Tri Suppli

Products

Machine Screws

We offer a variety of machine screws in stainless steel and other materials. Standard Hex Head, Phillips Drive, Slotted Drive, U Drive. We also offer non-standard and specialty screws not listed on our site. Contact us and request a quote today.

  • Indented Hex and Hex

    Standard hexagon head but with a washer section at the base of the head to protect the finish of the assembly from wrench disfigurement, and to economical.

    Standard hexagon head but with a washer section at the base of the head to protect the finish of the assembly from wrench disfigurement, and to economical.

  • Phillips Pan

    Recommended for new designs to replace round, truss and binding heads. Provides a low large diameter head, but with characteristically high outer edge along the outer periphery of the head. Most effective for high tightening torques.

    Recommended for new designs to replace round, truss and binding heads. Provides a low large diameter head, but with characteristically high outer edge along the outer periphery of the head. Most effective for high tightening torques.

  • Slotted Binder

    Most generally used in electrical and radio work because of its identifying undercut beneath the head, which binds and eliminates fraying of stranded wire. A medium - low head with ordinarily sufficient bearing surface.

    Most generally used in electrical and radio work because of its identifying undercut beneath the head, which binds and eliminates fraying of stranded wire. A medium - low head with ordinarily sufficient bearing surface.

  • Slotted Pan

    Recommended for new designs to replace round, truss and binding heads. Provides a low large diameter head, but with characteristically high outer edge along the outer periphery of the head. Most effective for high tightening torques.

    Recommended for new designs to replace round, truss and binding heads. Provides a low large diameter head, but with characteristically high outer edge along the outer periphery of the head. Most effective for high tightening torques.

  • Slotted Set Screws

    Slotted set screws, or grub screws as some like to call them, are fully threaded headless screws with a slot on one end and a with a variety of points available on the other. A slotted drive set screws does have some advantages since most everyone has a slotted screw drivers.

    Slotted set screws, or grub screws as some like to call them, are fully threaded headless screws with a slot on one end and a with a variety of points available on the other. A slotted drive set screws does have some advantages since most everyone has a slotted screw drivers.

 

  • Phillips Flat

    The standard flat or oval head 80° to 82° counter sunk screw will fit a standard counterbored hole and is particularly adaptable to flush assemblies in thin stock.

    The standard phillips flat head supplied 80° to 82° angle to be used where finished surfaces require flush fastening The counter sunk portion offers good centering possibilities

  • Phillips Round

    A round head machine screws is a usually threaded to the head. Made of stainless steel and with slot or phillips drive, and are used to join sheet metal parts using a hex or square nut. Not recommended for new design (see pan head)

    A round head machine screws is a usually threaded to the head. Made of stainless steel and with slot or phillips drive, and are used to join sheet metal parts using a hex or square nut. Not recommended for new design (see pan head).

  • Slotted Fillister

    The standard oval fillister head has a smaller diameter than the round head, but is higher with a correspondingly deeper slot. The small diameter head increases the pressure applied on the smaller area and can be assembled close flanges.

    The standard oval fillister head has a smaller diameter than the round head, but is higher with a correspondingly deeper slot. The small diameter head increases the pressure applied on the smaller area and can be assembled close flanges.

  • Slotted Round

    A round head machine screws is a usually threaded to the head. Made of stainless steeland with slot or phillips drive, and are used to join sheet metal parts using a hex or square nut .Not recommended for new design (see pan head)

    A round head machine screws is a usually threaded to the head. Made of stainless steel and with slot or phillips drive, and are used to join sheet metal parts using a hex or square nut .Not recommended for new design (see pan head)

  • Socket Jam Screws

    Socket jam screws are used to lock set screws, springs, and controls into tapped holes. The full length hex socket permits access from either end or visual inspection of the locked part. The controlled socket dimensions give good wrenchability for reuse time after time.

    Socket jam screws are used to lock set screws, springs, and controls into tapped holes. The full length hex socket permits access from either end or visual inspection of the locked part. The controlled socket dimensions give good wrench-ability for reuse time after time.

 

  • Phillips Oval

    The standard flat or oval head 80° to 82° counter sunk screw will fit a standard counterbored hole and is particularly adaptable to flush assemblies in thin stock.

    The standard phillips oval head supplied 80° to 82° angle to be used where finished surfaces require flush fastening The counter sunk portion offers good centering possibilities

  • Phillips Truss

    Also known as oven head, stove head, and oval binding head. A low, large diameter head that can be used to cover larger diameter clearance holes in sheet metal when additional play in assembly tolerance is required.

    Also known as oven head, stove head, and oval binding head. A low, large diameter head that can be used to cover larger diameter clearance holes in sheet metal when additional play in assembly tolerance is required.

  • Slotted Oval

    The standard oval head 80° to 82° counter sunk screw with a rounded surface and a cone-shaped bearing surface. Will fit a standard counterbored hole and adaptable to a flush surface. Preferred when decorative finish is desired.

    The standard slotted oval head 80° to 82° counter sunk screw with a rounded surface and a cone-shaped bearing surface. Will fit a standard counter-bored hole and adaptable to a flush surface. Preferred when decorative finish is desired.

  • Slotted Truss

    Also known as oven head, stove head, and oval binding head. A low, large diameter head that can be used to cover larger diameter clearance holes in sheet metal when additional play in assembly tolerance is required.

    Also known as oven head, stove head, and oval binding head. A low, large diameter head that can be used to cover larger diameter clearance holes in sheet metal when additional play in assembly tolerance is required.

  • U Drive Screws

    Type U Drive Screws also known as hammer drive screw are unslotted round head self-tapping screws used for making permanent fastenings in metal and plastics, such as securing nameplates in castings. They require a predrilled hole and can be installed with a hammer.

    Type U Drive Screws also known as hammer drive screw are un-slotted round head self-tapping screws used for making permanent fastenings in metal and plastics, such as securing nameplates in castings. They require a pre-drilled hole and can be installed with a hammer.

Get A Quote Today

How may we help?

We offer a wide variety of purchasing choices. From our line of packaged products on Amazon to special programs that help your business succeed!

We offer a wide variety of purchasing choices. From our line of packaged products on Amazon to special programs that help your business succeed!
All the information provided in this section has been assembled with concern for accuracy. It is intended for advisory purposes only and use of this information is completely voluntary

Disclaimer

All the information provided in this section has been assembled with concern for accuracy. It is intended for advisory purposes only and use of this information is completely voluntary.