Fastener Measurements | Fastener Guides | Tri Suppli

Fastener Measurement Guide

Lead Thread

The distance a screw thread advances axially in one turn. CUT THREAD: Threads are cut or chased; the un-threaded portion of shank will be equal to major diameter of thread.

Rolled Thread

Threads are cold formed by squeezing the blank between reciprocating serrated dies. This acts to increase the major diameter of the thread over and above the diameter of un-threaded shank (if any), unless an extruded blank is used. Classes of thread are distinguished from each other by the amounts of tolerance and allowance specified. External threads or bolts are designated with the suffix "A", internal or nut threads with "B". CLASSES 1A and 1B:

For work of rough commercial quality where loose fit for spin-on-assembly is desirable. CLASSES 2A and 2B: The recognized standard for normal production of the great bulk of commercial bolts, nuts and screws. CLASSES 3A and 3B: Used where a closed fit between mating parts for high quality work is required. CLASS 4: A theoretical rather than practical class, now obsolete. CLASS 5: For a wrench fit. Used principally for studs and their mating tapped holes. A force fit requiring the application of high torque for semipermanent assembly.

  • A. Full Diameter Shank

    Equal to major diameter of thread. Produced by cut thread or by roll thread on extruded blank. Characteristic of machine bolts and cap screws.

  • B. Undersized Shank

    Equal approximately to pitch diameter of thread. Produced by roll threading a non-extruded blank. Characteristic of machine screws.

  • C. Pitch

    The distance from a point on the screw thread to the corresponding point on the next thread measured parallel to the axis.



  • A. Full Diameter Shank
Equal to major diameter of thread. Produced by cut thread or by roll thread on extruded blank. Characteristic of machine bolts and cap screws.



B. Undersized Shank
Equal approximately to pitch diameter of thread. Produced by roll threading a nonextruded blank. Characteristic of machine screws. 



C. Pitch
The distance from a point on the screw thread to the corresponding point on the next thread measured parallel to the axis. D. Pitch Diameter
The simple, effective diameter of screw thread. Approximately half way between the major and minor diameters. 



E. Major Diameter
The largest diameter of a screw thread. 



F. Minor Diameter The smallest diameter of a screw thread.Lead Thread


The distance a screw thread advances axially in one turn. CUT THREAD: Threads are cut or chased; the unthreaded portion of shank will be equal to major diameter of thread. 

Rolled Thread 

Threads are cold formed by squeezing the blank between reciprocating serrated dies. This acts to increase the major diameter of the thread over and above the diameter of unthreaded shank (if any), unless an extruded blank is used. Classes of thread are distinguished from each other by the amounts of tolerance and allowance specified. External threads or bolts are designated with the suffix "A", internal or nut threads with "B". CLASSES 1A and 1B: 

For work of rough commercial quality where loose fit for spin-on-assembly is desirable. CLASSES 2A and 2B: The recognized standard for normal production of the great bulk of commercial bolts, nuts and screws. CLASSES 3A and 3B: Used where a closed fit between mating parts for high quality work is required. CLASS 4: A theoretical rather than practical class, now obsolete. CLASS 5: For a wrench fit. Used principally for studs and their mating tapped holes. A force fit requiring the application of high torque for semipermanent assembly.

     

     

  • D. Pitch Diameter

    The simple, effective diameter of screw thread. Approximately half way between the major and minor diameters.

  • E. Major Diameter

    The largest diameter of a screw thread.

  • F. Minor Diameter

    The smallest diameter of a screw thread

DISCLAIMER

All the information provided in this section has been assembled with concern for accuracy. It is intended for advisory purposes only and use of this information is completely voluntary. We do not guarantee its completeness or validity and assume no responsibility for any loss, claims or damages resulting from use or application of this information. All information is subject to change without prior notice. Be sure to verify!All the information provided in this section has been assembled with concern for accuracy. It is intended for advisory purposes only and use of this information is completely voluntary. We do not guarantee its completeness or validity and assume no responsibility for any loss, claims or damages resulting from use or application of this information. All information is subject to change without prior notice.